G-TEC TTCF-9B : High Flow Heated Cooler Line Flusher (Base Model)

Product Description

Key Product Features:

• Heavy-duty 8 GPM flow rate: Delivers high-volume circulation for cleaning large transmission coolers, long cooler lines, and compatible hydraulic systems.
• Fixed high-flow base configuration: Provides straightforward 8 GPM operation for facilities that do not require variable-speed control or programmable flushing cycles.
• Transmission and hydraulic applications: Designed to clean heavy-duty transmission cooling circuits as well as compatible hydraulic lines, coolers, and components.
• Heated component flushing: Circulates heated fluid to soften sludge, waxy varnish, oxidized fluid deposits, and other contamination inside cooler passages.
• Uses system-compatible fluid: Operates with the same hydraulic or transmission fluid used by the system being cleaned rather than volatile solvents or mineral spirits.
• 1,500-watt heater: Provides direct fluid heating for more effective removal of hardened deposits and contamination.
• Preset 140°F operating temperature: The heater is factory-set to bring the flushing fluid to approximately 140°F.
• Approximately 45-minute heat-up: Manufacturer information states that the machine can reach its preset temperature in about 45 minutes under normal operating conditions.
• Flush with or without heat: Allows the technician to circulate fluid with the heating system enabled or disabled, depending on the component and service procedure.
• Powerful 3/4 HP motor: Supports the continuous high-volume flow required for heavy-duty cooler and hydraulic-system cleaning.
• Two preset air-injected flush patterns: Lets the technician select between two manually controlled patterns designed to introduce an effective amount of air into the fluid stream.
• Agitating air-scrub action: Air injection increases turbulence inside the connected system, helping break loose trapped debris and solidified varnish.
• Manual flushing control: Supports a manually operated flush when a preset air-injection pattern is not required.
• Manual air purge: Uses compressed shop air to increase agitation during cleaning or clear residual fluid from the cooling system and service hoses after flushing.
• Manual flow-reversing valve: Allows the operator to change flushing direction without disconnecting or exchanging the service hoses.
• Bidirectional system cleaning: Reversing fluid direction helps attack contamination from both sides of cooler passages and hydraulic circuits.
• Reusable 60-micron screen filter: Captures visible particles and lets technicians inspect removed debris to help verify system cleanliness.
• Cleanable filter design: The screen can be removed, cleaned, inspected, and reused between services.
• Dual non-bypass spin-on filters: Two replaceable magnetic system filters help capture fine debris and metallic particles without allowing unfiltered fluid to bypass the filter media.
• Replacement filter compatibility: Manufacturer specifications identify spin-on filter part number 40300272 for the system.
• Low-fluid heater cutoff: A float switch disables the heater if reservoir fluid drops below a safe operating level.
• Temperature gauge: Allows technicians to monitor fluid temperature during heating and flushing.
• Hour-run meter: Tracks total machine operation to support routine service, fluid replacement, and filter-maintenance scheduling.
• 10-gallon fluid capacity: Provides sufficient working-fluid volume for heavy-duty cooler and hydraulic-system flushing while maintaining a mobile footprint.
• Fluid-level sight glass: Gives technicians a clear visual indication of the fluid level inside the reservoir.
• 13-foot heavy-duty service hoses: Long 3/4-inch hoses provide the reach and internal capacity required for servicing large vehicles and industrial components.
• Heavy-duty mobility: Ten-inch semi-pneumatic tires make the machine easier to move across shop floors and position near large vehicles.
• Electrical requirements: Requires a dedicated 20-amp circuit or two separate 15-amp circuits for proper heater and pump operation.
• Available Allison adapter kit: An optional kit provides connections for several common JIC sizes used on Allison and other heavy-duty applications.
• Automotive adapter conversion available: An optional adapter kit reduces the heavy-duty hose couplers for use with compatible automotive flushing adapters.
• Manufacturer part number: 40400061.
• Professional applications: Ideal for heavy-duty truck service facilities, transmission rebuilders, fleet maintenance departments, construction and agricultural equipment shops, hydraulic repair centers, and vocational training facilities.

Why Buy from ProQuip Solutions:

Purchase the G-TEC TTCF-9B from ProQuip Solutions for dependable high-flow cleaning of heavy-duty transmission cooling circuits and hydraulic systems. ProQuip Solutions can assist with compatible adapter kits, replacement filters, service hoses, fittings, and maintenance components, helping professional facilities remove harmful contamination, protect replacement equipment, and reduce costly repeat repairs.